 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
|
Unimodule "METD" Series
SPECIFICATIONS
| Filters |
| Aluminum framed High Efficiency Particulate Air (HEPA) type, with a minimum efficiency of 99.99% at 0.3 micron, aerosol challenged (zero probed). |
| Prefilters |
| Disposable - 30% ASHRAE. Standard top mounted prefilter assembly interchangeable to the front. |
| Airflow |
| 90 FPM (.45 m/s) ±10 FPM (.05 m/s) average velocity measured 6 inches from the diffuser screen. Uniformity ±20% of average or better. |
| Motor/Blower Assembly |
| Direct drive, continuous duty with sealed-for-life bearings and inherent overload protection. Motor/blower assembly is electronically balanced (dynamically) and mounted on vibration dampening rubber mounts. Motor/blower assembly is designed to provide rated airflow through a 50% increase in initial static pressure. |
| Speed Controller |
| Solid state speed control (with RFI suppression), for adjusting airflow velocity. |
| Electrical |
Standard 115 V, single phase, 60 Hz with 7/8-inch conduit knock-out located on top of the M-2 air module. Optional power cord available. Recessed fluorescent lighting fixture provides 150 foot candles at the work surface. Separate blower and light switches. ETL listed. |
| Construction |
| Basic Exhausted Work Station |
Welded steel Unimodule M-2 air supply module with exterior finished in corrosion resistant polyurethane enamel. Tubular steel supports with welded joints, finished to match the M-2 air supply module. Complete with leveling feet with neoprene caps and retainer pins for positioning or holding the M-2 air supply module. Foam gasket, field-installed between stand and air module, provides an airtight seal. #304 stainless steel construction for upper and lower exhaust plenums, side enclosure panels, work deck and exhaust tub. Hinged 15-in. (381 mm) acrylic view screen. Stainless steel transition duct with 12 in. (304 mm) diameter exhaust collar. |
| Work Deck |
Removable 17.25 in. (438.15 mm) solid center stainless steel work surface. 51% open stainless steel front and rear exhaust grilles. Optional faucets and lab services mount from below and on either side of the solid stainless steel work surface without penetrating the exhaust tub. |
| 10 Inch Deep Exhaust Tub |
Located below the work deck permits use of liquids. Solid stainless steel tub slopes to a center drain. Watertight to 3/4 in. (19.05 mm) liquid depth. |
| Warranty |
| Limited one year. |
| Applications |
|
| Options |
|
 |
|||||
| Model Number |
Part Number |
Dimensions in Inches (millimeters) | |||
| A | B | C | D | ||
| METD 424 | 10662 | 52.24 (1279.8) |
34.00 (833) |
26.00 (637) |
31.50 (771.75) |
| METD 624 | 10663 | 76.24 (1867.8) |
34.00 (833) |
26.00 (637) |
31.50 (771.75) |
| METD 824 | 10664 | 100.24 (2455.8) |
34.00 (833) |
26.00 (637) |
31.50 (771.75) |
| Model Number |
Part Number |
Dimensions in Inches (millimeters) | Ship
Wt. lbs. (kilograms) |
|||
| E | F | G | H | |||
| METD 424 | 10662 | 27.50 (673.75) |
6.00 (147) |
37.50 (952.5) |
105.5 (2679.7) |
425 (192.78) |
| METD 624 | 10663 | 27.50 (673.75) |
6.00 (147) |
37.50 (952.5) |
105.5 (2679.7) |
615 (278.96) |
| METD 824 | 10664 | 27.50 (673.75) |
6.00 (147) |
37.50 (952.5) |
105.5 (2679.7) |
780 (353.8) |
| Model Number |
Part Number |
Opening,
Inches (millimeters) |
|
| Width | Height | ||
| METD 424 | 10662 | 46.94 (1150) |
11.00 (269.5) |
| METD624 | 10663 | 70.94 (1738) |
11.00 (269.5) |
| METD 824 | 10664 | 94.94 (2326) |
11.00 (269.5) |
| Model Number |
Face
m3/hr @ 105 FPM (.53 m/s) |
Supply
m3/hr @ 90 FPM (.45 m/s) |
Total
Exhaust Volume CFM (m3/hr) |
BTU/ Hour |
| METD 424 | 376* (639) |
720* (1224) |
1096* (1836) |
3460* |
| METD624 | 569* (967) |
1080* (1836) |
1649* (2803) |
5944* |
| METD 824 | 761* (1294) |
1440* (2448) |
2201* (3742) |
6060* |
For
additional information,
please contact your local Representative or
Distributor..
